Product Variations
Product Variations
LCD MPPT Solar Regulator
The Microcare Maximum Power Point Tracker Regulator is designed to interface between the solar panel and the batteries. The tracker will always find the optimum power point of the solar panel system to ensure that maximum power is extracted from the solar panel and put into the batteries. Using this system up to 30% more power can be extracted from the solar panel than using shunt or series PWM regulators. The MPPT charge controller will deliver the highest charge current possible for a given set of operating conditions. The ability to step down a high voltage solar array to a low voltage battery can save you money by reducing the size of the wire required and making the installation simpler and faster.
- Automatic selection of Battery voltage (24 – 48V)
- Input panel voltage (20-150Voc)
- Circuit Breaker protection – Full input and output protection
- Electronic current limiting.
- 4 Line LCD Display: Battery Voltage, Charge Mode (Equalize, Boost and Float) showing Charge Current, Panel Voltage and Output Power from the Panels
- Data Logger: 24hr Average and 63 day logger
- Programmable features
- Accessories. Battery/ Temperature Sensors, Daylight Switch, Relay Interface. Radio Link.
- Peak efficiency greater than 96%
- Advanced constant Power Point Tracking algorithm.
LCD MPPT Solar Regulator
The ability to step down a high voltage solar array to a low voltage battery can save you money by reducing the size of the wire required and making the installation simpler and faster. The 400V Mini Grid HV MPPT is designed as part of the Microcare Modular Mini-Grid Solution for both single and three-phase applications.
- Automatic selection of Battery voltage (24 – 48V)
- Input panel voltage (20-150Voc)
- Circuit Breaker protection – Full input and output protection
- Electronic current limiting.
- 4 Line LCD Display: Battery Voltage, Charge Mode (Equalize, Boost and Float) showing Charge Current, Panel Voltage and Output Power from the Panels
- Data Logger: 24hr Average and 63 day logger
- Programmable features
- Accessories. Battery/ Temperature Sensors, Daylight Switch, Relay Interface. Radio Link.
- Peak efficiency greater than 96%
- Advanced constant Power Point Tracking algorithm.
LCD MPPT Solar Regulator
The Microcare Maximum Power Point Tracker Regulator is designed to interface between the solar panel and the batteries. The tracker will always find the optimum power point of the solar panel system to ensure that maximum power is extracted from the solar panel and put into the batteries. Using this system up to 30% more power can be extracted from the solar panel than using shunt or series PWM regulators. The MPPT charge controller will deliver the highest charge current possible for a given set of operating conditions. The ability to step down a high voltage solar array to a low voltage battery can save you money by reducing the size of the wire required and making the installation simpler and faster.
- Automatic selection of Battery voltage (24 – 48V)
- Input panel voltage (20-150Voc)
- Circuit Breaker protection – Full input and output protection
- Electronic current limiting.
- 4 Line LCD Display: Battery Voltage, Charge Mode (Equalize, Boost and Float) showing Charge Current, Panel Voltage and Output Power from the Panels
- Data Logger: 24hr Average and 63 day logger
- Programmable features
- Accessories. Battery/ Temperature Sensors, Daylight Switch, Relay Interface. Radio Link.
- Peak efficiency greater than 96%
- Advanced constant Power Point Tracking algorithm.
5.2kW 400V Mini-Grid HV MPPT
The ability to step down a high voltage solar array to a low voltage battery can save you money by reducing the size of the wire required and making the installation simpler and faster. The 400V Mini Grid HV MPPT is designed as part of the Microcare Modular Mini-Grid Solution for both single and three-phase applications.
- Input panel voltage 400V Max
- 48V Battery pack
- Input and output protection
- Electronic current limiting.
- 4x4 Line LCD Display:
- Battery Voltage,
- Charge Mode (Equalize, Boost and Float) showing Charge Current,
- Panel Voltage and
- Output Power from the Panels
- Data Logger: 24hr Average and 63 day logger
- Programmable features
- Peak efficiency greater than 96%
- Advanced constant Power Point Tracking algorithm
LED MPPT Solar Regulator
The Microcare Maximum Power Point Tracker Regulator is designed to interface between the solar panel, the batteries and the load. The tracker will always find the optimum power point of the solar panel system to ensure that maximum power is extracted from the solar panel and put into the batteries. Using this system up to 30% more power can be extracted from the solar panel than using shunt or series PWM regulators.
The Microcare MPPT Regulator is also able to charge batteries of a lower voltage than the solar panel. By means of LED it will show the status of the system. It also incorporates various charge modes which will automatically increase the charge level to the batteries when first starting up or if the battery voltage falls below the minimum volts.
- Automatically measures the battery voltage and then sets up the charge parameters (12 or 24V)
- Operates the Solar Panels at the maximum efficiency
- Can improve power extracted from the solar panels by 30% over normal shunt/series PWM regulators
- LED status notification
- Temperature controlled Cooling Fan
- Selectable low voltage disconnect
- 24 hour load shed or Day/Night mode
- 24 hour load shed or Day/Night mode
- Charges batteries by setting up the best power point of the solar panels
LED MPPT Solar Regulator
The Microcare Maximum Power Point Tracker Regulator is designed to interface between the solar panel, the batteries and the load. The tracker will always find the optimum power point of the solar panel system to ensure that maximum power is extracted from the solar panel and put into the batteries. Using this system up to 30% more power can be extracted from the solar panel than using shunt or series PWM regulators.
The Microcare MPPT Regulator is also able to charge batteries of a lower voltage than the solar panel. By means of LED it will show the status of the system. It also incorporates various charge modes which will automatically increase the charge level to the batteries when first starting up or if the battery voltage falls below the minimum volts.
- Automatically measures the battery voltage and then sets up the charge parameters (12 or 24V)
- Operates the Solar Panels at the maximum efficiency
- Can improve power extracted from the solar panels by 30% over normal shunt/series PWM regulators
- LED status notification
- Temperature controlled Cooling Fan
- Selectable low voltage disconnect
- 24 hour load shed or Day/Night mode
- 24 hour load shed or Day/Night mode
- Charges batteries by setting up the best power point of the solar panels
Remote Programmable Relay
The Microcare Programmable Relay Interface can be used in conjunction with any of the Microcare LCD MPPT range. The MPPT can be programmed to switch the relay at selectable voltages, conditions and parameters. The Programmable Relay Interface can be used as a Load shed controller, Day night switch, Generator controller or to facilitate our Solar Assist Function where the MPPT decides (based on user selectable conditions) when to power the LOAD / House using Solar / Wind power and when to power the LOAD / House via an external supply (like Eskom or a backup generator).
Load Shed Controller
– Relay switches off when battery voltage falls below the user selected battery low voltage.
– Relay switches on when battery voltage rises above the user selected battery good voltage.
Day Night Switch
– Relay switches on when panel voltage falls below the battery voltage.
– Relay switches off when panel voltage rises above the battery voltage.
General Controller
– Same operation as Load shed controller.
– Connect COM – NC (normally close) connections to generator remote start.
Solar Assist Function
– Same operation as Load shed controller
Remote Programmable Relay
The Microcare Programmable Relay Interface can be used in conjunction with any of the Microcare LCD MPPT range. The MPPT can be programmed to switch the relay at selectable voltages, conditions and parameters. The Programmable Relay Interface can be used as a Load shed controller, Day night switch, Generator controller or to facilitate our Solar Assist Function where the MPPT decides (based on user selectable conditions) when to power the LOAD / House using Solar / Wind power and when to power the LOAD / House via an external supply (like Eskom or a backup generator).
Load Shed Controller
– Relay switches off when battery voltage falls below the user selected battery low voltage.
– Relay switches on when battery voltage rises above the user selected battery good voltage.
Day Night Switch
– Relay switches on when panel voltage falls below the battery voltage.
– Relay switches off when panel voltage rises above the battery voltage.
General Controller
– Same operation as Load shed controller.
– Connect COM – NC (normally close) connections to generator remote start.
Solar Assist Function
– Same operation as Load shed controller
Breakerless LV Combiner & Surge Protection Unit
The Microcare Breakerless Low Voltage Combiner & Surge Protection Unit is a critical component of any PV Solar installation providing functions such as safety and surge protection for your system. With fusing and short circuit protection the PV modules and components can operate optimally with lightning protection included. Combining multiple series strings from the PV modules the unit allows for a single parallel connection to the MPPT charge controller.
- Available for combining 1 to 6 Series PV Strings into 1 Output
- Surge / Lightning Protection
- Fuse Protection
- Easily connect PV arrays to solar equipment
- IP65 container
⬇ Download User Manual
